Muon-catalyzed fusion (abbreviated as μCF or MCF) is a process allowing nuclear fusion to take place at temperatures significantly lower than the temperatures required for thermonuclear fusion, even at room temperature or lower. It is one of the few known ways of catalyzing nuclear fusion reactions.

Muons are unstable subatomic particles which are similar to electrons but 207 times more massive. If a muon replaces one of the electrons in a hydrogen molecule, the nuclei are consequently drawn 186[1][2] times closer than in a normal molecule, due to the reduced mass being 186 times the mass of an electron. When the nuclei move closer together, the fusion probability increases, to the point where a significant number of fusion events can happen at room temperature.

Methods for obtaining muons, however, require far more energy than can be produced by the resulting fusion reactions. Muons have a mean lifetime of 2.2 μs, much longer than many other subatomic particles but nevertheless far too brief to allow their useful storage.[3]

To create useful room-temperature muon-catalyzed fusion, reactors would need a cheap, efficient muon source and/or a way for each individual muon to catalyze many more fusion reactions.

History

Andrei Sakharov and F.C. Frank[4] predicted the phenomenon of muon-catalyzed fusion on theoretical grounds before 1950. Yakov Borisovich Zel'dovich[5] also wrote about the phenomenon of muon-catalyzed fusion in 1954. Luis W. Alvarez et al.,[6] when analyzing the outcome of some experiments with muons incident on a hydrogen bubble chamber at Berkeley in 1956, observed muon-catalysis of exothermic p–d, proton and deuteron, nuclear fusion, which results in a helion, a gamma ray, and a release of about 5.5 MeV of energy. The Alvarez experimental results, in particular, spurred John David Jackson to publish one of the first comprehensive theoretical studies of muon-catalyzed fusion in his ground-breaking 1957 paper.[7] This paper contained the first serious speculations on useful energy release from muon-catalyzed fusion. Jackson concluded that it would be impractical as an energy source, unless the "alpha-sticking problem" (see below) could be solved, leading potentially to an energetically cheaper and more efficient way of utilizing the catalyzing muons.[7]

Viability as a power source

Potential benefits

If muon-catalyzed d–t nuclear fusion is realized practically, it will be a much more attractive way of generating power than conventional nuclear fission reactors because muon-catalyzed d–t nuclear fusion (like most other types of nuclear fusion), produces far fewer harmful (and far less long-lived) radioactive wastes.

The large number of neutrons produced in muon-catalyzed d–t nuclear fusions may be used to breed fissile fuels, from fertile material – for example, thorium-232 could breed uranium-233 in this way.[note 1] The fissile fuels that have been bred can then be "burned," either in a conventional critical nuclear fission reactor or in an unconventional subcritical fission reactor, for example, a reactor using nuclear transmutation to process nuclear waste, or a reactor using the energy amplifier concept devised by Carlo Rubbia and others.

Another benefit of muon-catalyzed fusion is that the fusion process can start with pure deuterium gas without tritium. Plasma fusion reactors like ITER or Wendelstein X7 need tritium to initiate and also need a tritium factory. Muon-catalyzed fusion generates tritium under operation and increases operating efficiency up to an optimum point when the deuterium:tritium ratio reaches about 1:1. Muon-catalyzed fusion can operate as a tritium factory and deliver tritium for material and plasma fusion research.

Problems facing practical exploitation

Except for some refinements, little has changed since Jackson's 1957 assessment of the feasibility of muon-catalyzed fusion other than Vesman's 1967 prediction of the hyperfine resonant formation of the muonic (d–μ–t)+ molecular ion which was subsequently experimentally observed. This helped spark renewed interest in the whole field of muon-catalyzed fusion, which remains an active area of research worldwide. However, as Jackson observed in his paper, muon-catalyzed fusion is "unlikely" to provide "useful power production ... unless an energetically cheaper way of producing μ-mesons[note 2] can be found."[7]

One practical problem with the muon-catalyzed fusion process is that muons are unstable, decaying in 2.2 μs (in their rest frame).[8] Hence, there needs to be some cheap means of producing muons, and the muons must be arranged to catalyze as many nuclear fusion reactions as possible before decaying.

Another, and in many ways more serious, problem is the "alpha-sticking" problem, which was recognized by Jackson in his 1957 paper.[7][note 3] The α-sticking problem is the approximately 1% probability of the muon "sticking" to the alpha particle that results from deuteron-triton nuclear fusion, thereby effectively removing the muon from the muon-catalysis process altogether. Even if muons were absolutely stable, each muon could catalyze, on average, only about 100 d-t fusions before sticking to an alpha particle, which is only about one-fifth the number of muon catalyzed d–t fusions needed for break-even, where as much thermal energy is generated as electrical energy is consumed to produce the muons in the first place, according to Jackson's rough estimate.[7]

More recent measurements seem to point to more encouraging values for the α-sticking probability, finding the α-sticking probability to be around 0.3% to 0.5%, which could mean as many as about 200 (even up to 350) muon-catalyzed d–t fusions per muon.[9] Indeed, the team led by Steven E. Jones achieved 150 d–t fusions per muon (average) at the Los Alamos Meson Physics Facility.[10] The results were promising and almost enough to reach theoretical break-even. Unfortunately, these measurements for the number of muon-catalyzed d–t fusions per muon are still not enough to reach industrial break-even. Even with break-even, the conversion efficiency from thermal energy to electrical energy is only about 40% or so, further limiting viability. The best recent estimates of the electrical "energy cost" per muon is about 6 GeV with accelerators that are (coincidentally) about 40% efficient at transforming electrical energy from the power grid into acceleration of the deuterons.

As of 2012, no practical method of producing energy through this means has been published, although some discoveries using the Hall effect show promise.[11]

Alternative estimation of breakeven

According to Gordon Pusch, a physicist at Argonne National Laboratory, various breakeven calculations on muon-catalyzed fusion omit the heat energy the muon beam itself deposits in the target.[12] By taking this factor into account, muon-catalyzed fusion can already exceed breakeven; however, the recirculated power is usually very large compared to power out to the electrical grid (about 3–5 times as large, according to estimates). Despite this rather high recirculated power, the overall cycle efficiency is comparable to conventional fission reactors; however the need for 4–6 MW electrical generating capacity for each megawatt out to the grid probably represents an unacceptably large capital investment. Pusch suggested using Bogdan Maglich's "migma" self-colliding beam concept to significantly increase the muon production efficiency, by eliminating target losses, and using tritium nuclei as the driver beam, to optimize the number of negative muons.

In 2021, Kelly, Hart and Rose [13] produced a μCF model whereby the ratio, Q, of thermal energy produced to the kinetic energy of the accelerated deuterons used to create negative pions (and thus negative muons through pion decay) was optimized. In this model, the heat energy of the incoming deuterons as well as that of the particles produced due to the deuteron beam impacting a tungsten target was recaptured to the extent possible, as suggested by Gordon Pusch in the previous paragraph. Additionally, heat energy due to tritium breeding in a lithium-lead shell was recaptured, as suggested by Jändel, Danos and Rafelski in 1988.[14] The best Q value was found to be about 130% assuming that 50% of the muons produced were actually utilized for fusion catalysis. Furthermore, assuming that the accelerator was 18% efficient at transforming electrical energy into deuteron kinetic energy and conversion efficiency of heat energy into electrical energy of 60%, they estimate that, currently, the amount of electrical energy that could be produced by a μCF reactor would be 14% of the electrical energy consumed. In order for this to improve, they suggest that some combination of a) increasing accelerator efficiency and b) increasing the number of fusion reactions per negative muon above the assumed level of 150 would be needed.

Process

To create this effect, a stream of negative muons, most often created by decaying pions, is sent to a block that may be made up of all three hydrogen isotopes (protium, deuterium, and/or tritium), where the block is usually frozen, and the block may be at temperatures of about 3 kelvin (−270 degrees Celsius) or so. The muon may bump the electron from one of the hydrogen isotopes. The muon, 207 times more massive than the electron, effectively shields and reduces the electromagnetic repulsion between two nuclei and draws them much closer into a covalent bond than an electron can. Because the nuclei are so close, the strong nuclear force is able to kick in and bind both nuclei together. They fuse, release the catalytic muon (most of the time), and part of the original mass of both nuclei is released as energetic particles, as with any other type of nuclear fusion. The release of the catalytic muon is critical to continue the reactions. The majority of the muons continue to bond with other hydrogen isotopes and continue fusing nuclei together. However, not all of the muons are recycled: some bond with other debris emitted following the fusion of the nuclei (such as alpha particles and helions), removing the muons from the catalytic process. This gradually chokes off the reactions, as there are fewer and fewer muons with which the nuclei may bond. The number of reactions achieved in the lab can be as high as 150 d–t fusions per muon (average).

Deuterium–tritium (d–t or dt)

In the muon-catalyzed fusion of most interest, a positively charged deuteron (d), a positively charged triton (t), and a muon essentially form a positively charged muonic molecular heavy hydrogen ion (d–μ–t)+. The muon, with a rest mass 207 times greater than the rest mass of an electron,[8] is able to drag the more massive triton and deuteron 207 times closer together to each other[1] [2] in the muonic (d–μ–t)+ molecular ion than can an electron in the corresponding electronic (d–e–t)+ molecular ion. The average separation between the triton and the deuteron in the electronic molecular ion is about one angstrom (100 pm),[7][note 4] so the average separation between the triton and the deuteron in the muonic molecular ion is 207 times smaller than that.[note 5] Due to the strong nuclear force, whenever the triton and the deuteron in the muonic molecular ion happen to get even closer to each other during their periodic vibrational motions, the probability is very greatly enhanced that the positively charged triton and the positively charged deuteron would undergo quantum tunnelling through the repulsive Coulomb barrier that acts to keep them apart. Indeed, the quantum mechanical tunnelling probability depends roughly exponentially on the average separation between the triton and the deuteron, allowing a single muon to catalyze the d–t nuclear fusion in less than about half a picosecond, once the muonic molecular ion is formed.[7]

The formation time of the muonic molecular ion is one of the "rate-limiting steps" in muon-catalyzed fusion that can easily take up to ten thousand or more picoseconds in a liquid molecular deuterium and tritium mixture (D2, DT, T2), for example.[7] Each catalyzing muon thus spends most of its ephemeral existence of 2.2 microseconds,[8] as measured in its rest frame, wandering around looking for suitable deuterons and tritons with which to bind.

Another way of looking at muon-catalyzed fusion is to try to visualize the ground state orbit of a muon around either a deuteron or a triton. Suppose the muon happens to have fallen into an orbit around a deuteron initially, which it has about a 50% chance of doing if there are approximately equal numbers of deuterons and tritons present, forming an electrically neutral muonic deuterium atom (d–μ)0 that acts somewhat like a "fat, heavy neutron" due both to its relatively small size (again, 207 times smaller than an electrically neutral electronic deuterium atom (d–e)0) and to the very effective "shielding" by the muon of the positive charge of the proton in the deuteron. Even so, the muon still has a much greater chance of being transferred to any triton that comes near enough to the muonic deuterium than it does of forming a muonic molecular ion. The electrically neutral muonic tritium atom (t–μ)0 thus formed will act somewhat like an even "fatter, heavier neutron," but it will most likely hang on to its muon, eventually forming a muonic molecular ion, most likely due to the resonant formation of a hyperfine molecular state within an entire deuterium molecule D2 (d=e2=d), with the muonic molecular ion acting as a "fatter, heavier nucleus" of the "fatter, heavier" neutral "muonic/electronic" deuterium molecule ([d–μ–t]=e2=d), as predicted by Vesman, an Estonian graduate student, in 1967.[15]

Once the muonic molecular ion state is formed, the shielding by the muon of the positive charges of the proton of the triton and the proton of the deuteron from each other allows the triton and the deuteron to tunnel through the Coulomb barrier in time span of order of a nanosecond[16] The muon survives the d–t muon-catalyzed nuclear fusion reaction and remains available (usually) to catalyze further d–t muon-catalyzed nuclear fusions. Each exothermic d–t nuclear fusion releases about 17.6 MeV of energy in the form of a "very fast" neutron having a kinetic energy of about 14.1 MeV and an alpha particle α (a helium-4 nucleus) with a kinetic energy of about 3.5 MeV.[7] An additional 4.8 MeV can be gleaned by having the fast neutrons moderated in a suitable "blanket" surrounding the reaction chamber, with the blanket containing lithium-6, whose nuclei, known by some as "lithions," readily and exothermically absorb thermal neutrons, the lithium-6 being transmuted thereby into an alpha particle and a triton.[note 6]

Deuterium–deuterium and other types

The first kind of muon–catalyzed fusion to be observed experimentally, by L.W. Alvarez et al.,[6] was protium (H or 1H1) and deuterium (D or 1H2) muon-catalyzed fusion. The fusion rate for p–d (or pd) muon-catalyzed fusion has been estimated to be about a million times slower than the fusion rate for d–t muon-catalyzed fusion.[7][note 7]

Of more practical interest, deuterium–deuterium muon-catalyzed fusion has been frequently observed and extensively studied experimentally, in large part because deuterium already exists in relative abundance and, like protium, deuterium is not at all radioactive. (Tritium rarely occurs naturally, and is radioactive with a half-life of about 12.5 years.[8])

The fusion rate for d–d muon-catalyzed fusion has been estimated to be only about 1% of the fusion rate for d–t muon-catalyzed fusion, but this still gives about one d–d nuclear fusion every 10 to 100 picoseconds or so.[7] However, the energy released with every d–d muon-catalyzed fusion reaction is only about 20% or so of the energy released with every d–t muon-catalyzed fusion reaction.[7] Moreover, the catalyzing muon has a probability of sticking to at least one of the d–d muon-catalyzed fusion reaction products that Jackson in this 1957 paper[7] estimated to be at least 10 times greater than the corresponding probability of the catalyzing muon sticking to at least one of the d–t muon-catalyzed fusion reaction products, thereby preventing the muon from catalyzing any more nuclear fusions. Effectively, this means that each muon catalyzing d–d muon-catalyzed fusion reactions in pure deuterium is only able to catalyze about one-tenth of the number of d–t muon-catalyzed fusion reactions that each muon is able to catalyze in a mixture of equal amounts of deuterium and tritium, and each d–d fusion only yields about one-fifth of the yield of each d–t fusion, thereby making the prospects for useful energy release from d–d muon-catalyzed fusion at least 50 times worse than the already dim prospects for useful energy release from d–t muon-catalyzed fusion.

Potential "aneutronic" (or substantially aneutronic) nuclear fusion possibilities, which result in essentially no neutrons among the nuclear fusion products, are almost certainly not very amenable to muon-catalyzed fusion.[7] One such essentially aneutronic nuclear fusion reaction involves a deuteron from deuterium fusing with a helion (He+2) from helium-3, which yields an energetic alpha particle and a much more energetic proton, both positively charged (with a few neutrons coming from inevitable d–d nuclear fusion side reactions). However, one muon with only one negative electric charge is incapable of shielding both positive charges of a helion from the one positive charge of a deuteron. The chances of the requisite two muons being present simultaneously are exceptionally remote.

In culture

The term "cold fusion" was coined to refer to muon-catalyzed fusion in a 1956 New York Times article about Luis W. Alvarez's paper.[17]

In 1957 Theodore Sturgeon wrote a novelette, "The Pod in the Barrier", in which humanity has ubiquitous cold fusion reactors that work with muons. The reaction is "When hydrogen one and hydrogen two are in the presence of Mu mesons, they fuse into helium three, with an energy yield in electron volts of 5.4 times ten to the fifth power". Unlike the thermonuclear bomb contained in the Pod (which is used to destroy the Barrier) they can become temporarily disabled by "concentrated disbelief" that muon fusion works.[18]

In Sir Arthur C. Clarke's third novel in the Space Odyssey series, 2061: Odyssey Three, muon-catalyzed fusion is the technology that allows mankind to achieve easy interplanetary travel. The main character, Heywood Floyd, compares Luis Alvarez to Lord Rutherford for underestimating the future potential of their discoveries.

Notes

  1. The breeding takes place due to certain neutron-capture nuclear reactions, followed by beta decays, the ejection of electrons and neutrinos from nuclei as neutrons within the nuclei decay into protons as a result of weak nuclear forces.
  2. Muons are not mesons; they are leptons. However, this was not clear until 1947, and the name "mu meson" was still used for some time following the identification of the muon as a lepton.
  3. Eugene P. Wigner pointed out the α-sticking problem to Jackson.
  4. According to Cohen, S.; Judd, D.L.; Riddell, Jr., R.J. (1960). "μ-Mesonic Molecules. II. Molecular-Ion Formation and Nuclear Catalysis". Phys. Rev. 119 (1): 397. Bibcode:1960PhRv..119..397C. doi:10.1103/PhysRev.119.397., footnote 16, Jackson may have been overly optimistic in Appendix D of his 1957 paper in his roughly calculated "guesstimate" of the rate of formation of a muonic (p–μ–p)+ molecular ion by a factor of about a million or so.)
  5. In other words, the separation in the muonic case is about 500 femtometers
  6. "Thermal neutrons" are neutrons that have been "moderated" by giving up most of their kinetic energy in collisions with the nuclei of the "moderating materials" or moderators, cooling down to "room temperature" and having a thermalized kinetic energy of about 0.025 eV, corresponding to an average "temperature" of about 300 kelvins or so.
  7. In principle, of course, p–d nuclear fusion could be catalyzed by the electrons present in DO "heavy-ish" water molecules that naturally occur at the level of 0.0154% in ordinary water (H2O). However, because the proton and the deuteron would be more than 200 times farther apart in the case of the electronic HDO molecule than in the case of the muonic (p–μ–d)+ molecular ion, Jackson estimates that the rate of p–d "electron"-catalyzed fusion (eCF) is about 38 orders of magnitude (1038) slower than the rate of p–d muon-catalyzed fusion (μCF), which Jackson estimates to be about 106 per second, so p–d "electron"-catalyzed fusions (eCF) would be expected to occur at a rate of about 10−32 per second, meaning that one p–d "electron"-catalyzed fusion (eCF) might occur once every 1024 years or so.

References

  1. 1 2 Close, Frank E. (1992). Too Hot to Handle: The Race for Cold Fusion (2nd ed.). London: Penguin. pp. 32, 54. ISBN 0-14-015926-6.
  2. 1 2 Huizenga, John R. (1993). Cold Fusion: The Scientific Fiasco of the Century (2nd ed.). Oxford and New York: Oxford University Press. p. 112. ISBN 0-19-855817-1.
  3. Beringer, J. "Particle Data Group" (PDF).
  4. Frank, F.C. (1947). "Hypothetical Alternative Energy Sources for the 'Second Meson' Events". Nature. 160 (4068): 525–7. Bibcode:1947Natur.160..525F. doi:10.1038/160525a0. PMID 20269843.
  5. Zel'dovitch, Yakov Borisovich (1954). "Reactions caused by Miu-mesons in Hydrogen". Doklady Akademii Nauk SSSR. 95: 493. Bibcode:1954DoSSR..95..493Z.
  6. 1 2 Alvarez, L.W.; et al. (1957). "Catalysis of Nuclear Reactions by μ Mesons". Physical Review. 105 (3): 1127. Bibcode:1957PhRv..105.1127A. doi:10.1103/PhysRev.105.1127. S2CID 123886206.
  7. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Jackson, J.D. (1957). "Catalysis of Nuclear Reactions between hydrogen isotopes by μ-Mesons". Physical Review. 106 (2): 330. Bibcode:1957PhRv..106..330J. doi:10.1103/PhysRev.106.330.
  8. 1 2 3 4 The values of the various physical constants and masses can be found at the National Institute of Standards and Technology website NIST Constants, for example.
  9. Rafelski, J.; Jones, S.E. (1987). "Cold Nuclear Fusion". Scientific American. 257: 84. Bibcode:1987SciAm.257a..84R. doi:10.1038/scientificamerican0787-84.
  10. Jones, S.E. (1986). "Muon-Catalysed Fusion Revisited". Nature. 321 (6066): 127–133. Bibcode:1986Natur.321..127J. doi:10.1038/321127a0. S2CID 39819102.
  11. Negele, J. W.; Vogt, Erich (1998). Advances in nuclear physics (illustrated ed.). Springer. pp. 194–198. ISBN 9780306457579.
  12. Gordon Pusch (May 19, 1996). ""Migma" fusion". Newsgroup: sci.physics.fusion. Retrieved November 17, 2015.
  13. Kelly, R. S.; Hart, L. J. F.; Rose, S. J. (2021). "An investigation of efficient muon production for use in muon catalyzed fusion". Journal of Physics: Energy. 3 (3): 525–527. Bibcode:2021JPEn....3c5003S. doi:10.1088/2515-7655/abfb4b. hdl:10044/1/89136. PMID 20269843.
  14. Jändel, M.; Danos, M.; Rafelski, J. (1988). "Active target production of muons for muon-catalyzed fusion". Physical Review C. 37 (1): 403–406. Bibcode:1988PhRvC..37..403J. doi:10.1103/PhysRevC.37.403. PMID 9954454.
  15. Vesman, A. E. (1967). "Concerning one possible mechanism of production of the mesic-molecular ion (ddµ)+" (PDF). JETP Letters. 5 (4): 91–93.
  16. Balin, D. V.; et al. (2011). "High precision study of muon catalysed fusion in D2 and H2 gas". Physics of Particles and Nuclei. 42 (2): 185–214. Bibcode:2011PPN....42..185B. doi:10.1134/S106377961102002X. S2CID 120359203..
  17. Laurence, William L. (1956-12-30), "Cold Fusion of Hydrogen Atoms; A Fourth Method Pulling Together", The New York Times, pp. E7
  18. Sturgeon, Theodore (1957). "The Pod in the Barrier". Galaxy Science Fiction. 14: 8. (Also included in the collection A Touch of Strange, p. 17.)
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.