Yamaha XS Eleven[1]
1981 Yamaha XS Eleven Special
ManufacturerYamaha
Also calledXS1100, XS Eleven, XS1.1
Production1977 (MY1978) – 1983
ClassStandard
EngineAir cooled,1,101 cc (67.2 cu in) transverse four, DOHC, carb. (4) Mikuni BS34II constant velocity
Compression ratio1978-1979: 9.2:1 1980-1983: 9.0:1
Top speed135 mph (217 km/h)[2]
Power95 hp (71 kW) @8000rpm (claimed)[3]
Torque66.5 lb⋅ft (90.2 N⋅m) @6500rpm (claimed)[3]
Ignition typeTransistorized contact-less battery TCI, vacuum advance
Transmission5-speed with drive shaft
BrakesFront Dual 298 mm (11.7 in) single-piston floating caliper 
Rear Single 298 mm (11.7 in) single-piston floating caliper[2]
TiresFront 3.5H19 Bridgestone 
Rear 4.5H17 Bridgestone
Rake, trail20.5°, 130 mm (5.1 in)
Wheelbase1,530 mm (60.1 in)[4]
DimensionsW: 812 mm (32.0 in)
Seat height820 mm (32.3 in)
Weight603 lb (274 kg)[4] (wet)
Fuel capacityUS: 20 L (5.3 US gal) EU/RoW: 24 L (6.3 US gal)
Oil capacity3.5 L (3.7 US qt)
Fuel consumption40.3 mpgUS (5.8 l/100 km)

The Yamaha XS Eleven motorcycle, also called XS11 and XS1100, is a Japanese standard produced from 1977 (MY1978) to 1983, powered by an air-cooled 1,101 cc (67.2 cu in) 4-stroke, DOHC inline four-cylinder engine mounted transversely in a duplex cradle frame with swingarm rear suspension, shaft drive, and telescopic forks.[4]

History & Technology

The XS Eleven was the first four-cylinder four-stroke motorcycle from Yamaha.[4] It built on technology first used by Yamaha in their earlier XS 750 four-stroke triple. However, the XS 1100 engine design was a completely new design with several relatively unconventional elements compared to other inline 4-cylinder motorcycle engines of the day.

The XS 1100 four-cylinder engine maintained the same 68.6 mm stroke of the XS 750 triple but it had a larger bore of 71.5 mm (the XS 750 had a bore of 68 mm) and therefore became an "over-square" design. The camshaft drive chain moved to the center of the engine. The XS1100 engine does not transmit power directly from the crankshaft to the clutch basket/input shaft, but rather via a wide hy-vo chain onto an intermediate jack-shaft with a cush-drive damper.

XS 1100 Engine - Upper Half of the Engine Case with Crankshaft, Cam Chain, Hyvo-chain and Jackshaft Installed

The engine rotation was therefore clockwise when viewed from the left side and not counterclockwise as all other inline four-cylinder motorcycle engines of the day. This jackshaft included a "cush-drive" shock damper for drive shaft drive trains. The starter also engaged the jackshaft to start the engine. The engine is mounted in rubber bushings making it an almost completely vibration-free running powerplant.

A significant advancement of the XS 1100 engine are the combustion chambers.

XS 1100 Cylinder Head with Polyspherical Combustion Chambers

To make adequate power most modern motorcycle engines of the day including the XS 750 had simple hemispherical combustion chambers with domed pistons. This design has a major drawback in relatively long flame travel during combustion and therefore requires much spark advance, which in turn can cause severe preignition in high-performance engines. To improve combustion efficiency while virtually eliminating the possibility of preignition, Yamaha designed multi-angle "polyspheric" combustion chambers that required six different machining processes during manufacturing. This new design allowed for high compression without large piston domes and large ignition advance of over 40 degrees. The XS 1100 valves were the same as previously used in the XS 750 engine, but their angle differed from the previous 3-cylinder engine. Carburetion was delivered by four Mikuni BS34 II constant velocity (CV) carburetors and ignition via a contactless, transistorized electronic ignition unit (TCI) with vacuum advance.

When the XS Eleven was introduced, it immediately earned a reputation as a heavy, very powerful, and reliable bike. It was the fastest-ever production bike in 1978, for the first time posting a sub-12 second 1/4 mile time (11.78 sec. @ 114.21 mph with a top speed of 135 mph - Cycle World 2/78). In 1978 and 1979 it won Cycle World's Ten Best Bikes as the best Touring bike.[3]

"Nobody gets far riding the XS Eleven before they become acquainted with the fact that it's strong; we had ridden ours over hundreds of open-road miles before going to the drag strip and knew it was a bullet."[5] Cycle Magazine had this to say of the Eleven: "...the XS is a Rolls Royce with a blown Chrysler Hemi motor..."

The handling of the XS Eleven was not as well received. "When this behemoth of a motorcycle actually hits a corner at anything approaching interesting speeds then it takes a good deal of muscle to lay it down. While the Yamaha doesn't disgrace itself in corners (not as much as some Z1000s I have known, for example) it doesn't commend itself either."[6] Testers of the day all echoed the same story: "The XS1100 was a solid bullet in a straight line, but cornering at high speeds was done at your own risk."[4] "Cycle warned its readers that the bike could easily go, stop, and steer — just never two at the same time."[4] 'Which Bike' magazine simply described the XS1100 as having 'a bulletproof motor, and tea trolley handling'.

North American models

The XS Eleven made its debut in September 1977 (MY 1978) as the largest displacement motorcycle in production at that time. It featured a four-cylinder dual overhead cam engine, dual front disc brakes, a rear disc brake, shaft drive and cast aluminum wheels. The XS Eleven was the most powerful mass-production motorcycle of the late 70s and posted superior performance numbers compared to its competition.

The US market XS Eleven was launched as the so-called "Standard" model (Versions: E - 1978, F - 1979 and G - 1980-81). In 1979 Yamaha followed the growing market trend for "factory custom" motorcycles by offering the XS Eleven SF "Special". Pullback handlebars, a stepped seat, a 16-inch rear wheel, a smaller capacity tear-drop gas tank, and an adjustable suspension with new air-assisted leading-axle front forks created the factory custom look, forerunner of the modern cruiser. The XS Eleven Special sold well in the US. Despite complaints about the poor ergonomics "What that translates to is a bike with an awkward riding position but generally excellent road manners. In fact, most of the things that irritated this staff in the way the bike rode and handled could be traced to the handlebar, which, although certainly as trendy as disco dancing, was not what the ergonomics doctor ordered for precise, comfortable control."[7], it became the by far best-selling XS Eleven variant in the US market. In 1980 the XS Eleven LH "Midnight Special" was launched in all global markets including the US. It was basically an all black and gold version of the XS Eleven SF Special.

Beginning with the 1980 model year from September 1979 numerous changes were made to all XS Eleven engines in order to comply with more stringent US emission regulations. The compression ratio was dropped from 9.2:1 to 9.0:1 via changes to the pistons and cylinder head, increasing the volume of the combustion chamber and increasing the piston dome. The intake valve size was increased from 36 mm to 38 mm and the exhaust valve size from 31 mm to 32 mm in an attempt to compensate for the reduction in compression ratio. Ports of the late heads do flow better than early heads. Cam profiles and timing changed as well. Late cam intake and exhaust duration decreased by 12 degrees, while exhaust lift increased. Late cam LSA increased from 102 degrees to 105 degrees. In general early cams are worth about 2% more power than late cams. The 34mm Mikuni BS34 CV carbs remained in use but received different jetting and settings. From 1980 on there were no longer pilot jet adjustment screws installed. The jet needle was set in its leanest position. The main jets which were # 137.5 in all four carbs on 1978 and 1979 models, were reduced to #115 main jets in carbs two and three (center carbs) and # 120 main jets in carbs one and four (outside carbs). While Yamaha maintained identical performance specs on paper, period tests confirmed a slight reduction in the performance of the bike. These bikes never broke into the 11-second quarter mile as the 78-79 models had. Tests also commented that cold start and warm-up behavior had worsened noticeably and required unusually long operation of the cold start enrichment system. These 1980 - on "emission" XS Eleven bikes were easy to spot since a kickstarter shaft was no longer installed in the transmission and the kickstarter lever was no longer provided.

For the 1981 model year a dedicated touring model of the XS Eleven was launched, called the XS Eleven "Venturer". It was equipped with a full touring fairing made by Pacifico for Yamaha. XS Eleven Venturers also came with matching panniers and a top case. Additionally, the Venturer included the 6.3 gallon tank from the EU/RoW XS 1100 for an increased range and the oil cooler system of the EU/RoW XS1100.

The volume production of the XS Eleven really ended in 1981 in all markets and most XS Eleven models were superseded by the one-year-only 1982 XJ1100 Maxim, which used an advanced version of the XS1100 engine. In Europe however because of the importance of more sporting motorcycles, the XS 1.1 S was built as a "sport" model until 1982 (MY 1983) to bridge the gap until Yamaha could introduce the MY 1984 FJ 1100 (and subsequently FJ1200) sport-tourers in 1983.

1978 XS1100 E (EU 2H9)

European market XS 1100

In Europe, the XS 1100 "Standard" was by far the most popular model of the XS 1100 line-up. There the XS 1100 remained in production until 1983. The European Yamaha XS 1100 Standard (2H9) model differed considerably from the North American XS 1100 Standard (2H7) model (2H7 versions: E - 1978, F - 1979, and G - 1980-81). The EU XS 1100 Standard had a larger gas tank (6.3 gallons vs. 5.3 gallons), dual horns, and an EU-specific narrower, lower handlebar. The rider footpegs of the EU XS 1100 were mounted on different rear sets that positioned them higher and further back on the frame for more clearance. This required a shorter rear brake lever and a special linkage for a reversely mounted shift lever to work with these rear sets. Combined with the EU handlebar these rear sets allowed for a sportier riding position than the more relaxed, laid-back riding position of the US model. The EU and RoW XS1100 Standard had satin black painted engines equipped from the factory with an oil cooler system, while the US engines were all natural, unpainted aluminum without an oil cooler system. Further, the rear fender of the EU version was longer and the rear turn signals were mounted to the license plate holder instead of to the rear frame as in the US version. Many EU versions also had a separate steering head lock welded to the left side of the steering head as required by law in various EU countries.

While having been the by far most popular model in the US, the 1979 - 1981 XS 1100 SF "Special" sold rather poorly in Europe. It was, except for small differences required by law, identical to the US model. The European market also featured two limited production models: The 1979 XS1100 Martini with a two-piece fairing designed by John Mockett, sporting a Martini color scheme similar to the Martini promotion bike that Mike Hailwood used as his personal transport at the 1978 Isle of Man TT. Only 500 "Martinis" were ever built exclusively for the EU market of which 274 were sold in Germany and only 65 in the UK. The second limited-production model was the 1981 - 1983 XS 1.1 S (sold in Australia as the XS 1.1 R). A sporty version largely based on the XS 1100 Special but laid out more as a sports bike with a small cockpit fairing. Only 320 XS 1.1 S were sold since it was really a gap-filler model. Yamaha recognized the change in market demands for more sporty bikes and built the XS 1.1 S to bridge this gap until the new FJ 1100 was ready for sale. Both of these limited production models were not available in the US market. Production of the XS 1100 LH "Midnight Special" built from 1980 to 1982 was also limited, but to far greater numbers, and it was sold in all global markets.

Racing: Production and Modified Classes

The XS11 dominated the 1978 Australian motorcycle production racing circuit in 1978 and continued to victories and high place finishes in production and superbike classes through 1981. The XS Eleven's win at the 1978 Castrol Six Hour production endurance race by the Pittman's Team of Jim Budd and Roger Heyes was Yamaha's first four stroke motorcycle road racing victory at a major international event. "A key component of the race from the very start was that the motorcycles had to be completely stock, exactly as available the day after the race in dealers’ showrooms around the world, and they were rigorously inspected in both pre-race and post-race scrutineering to ensure that they were"

Flack of Motor Sport Retro wrote: "While the new CBX1000 and Suzuki were out and out sports bikes, the shaft-drive XS1100, affectionately called the 'Xcessive', was more of a muscle bike come tourer. Heavier than and not as fast as its rivals, the XS1100 did have one particular ability – winning races."[8]

"In the lead up to the Six-Hour, the XS1100 had swept the Adelaide Three-Hour, the Perth Four-Hour and the Surfers Three-Hour. The unlikely XS1100 and Pitman Yamaha rider Greg Pretty had upstaged the biggest, baddest production bikes around, confounding everyone."

In the 1979 Castrol 6 hour, XS Elevens finished second (Greg Pretty, Jim Budd) third (Len Atlee, Gary Coleman) and fourth (Roger Heyes and D. Robbins)

The XS Eleven's successful racing career was a remarkable achievement considering its shaft drive and long distance touring capabilities.

British motorcycle journalist Roland Brown, says in his book Superbikes of the Seventies: "The Yamaha's lack of reputation gives it one advantage these days, though, in that a clean XS such as this one costs less than its more successful contemporary rivals – whose performance advantage, so crucial then, is far less important now. Two decades and more after its launch, maybe the XS1100's time has finally come."

Performance

In a 1978 test by Cycle World a stock XS1100 ran a quarter mile time of 11.78 s 1/4 mile @114.21 mph (183.8 km/h) with a top speed of 135 mph (217.3 km/h).[3]


See also

References

  1. YAMAHA XS1100. Motorcyclist. January 1978. p. 29.
  2. 1 2 "Yamaha XS eleven test", Cycle, p. 40, March 1980, archived from the original on 22 March 2010
  3. 1 2 3 4 Cameron, Kevin (November 4, 2016). "Yamaha XS1100 - CLASSICS REMEMBERED". Cycle World. Retrieved February 28, 2017.
  4. 1 2 3 4 5 6 Mitchel, Doug (January–February 2010). "Yamaha XS1100". Motorcycle Classics. Retrieved 2010-05-21.
  5. Cycle, January 1978
  6. SuperBike, April 1978
  7. Cycle Guide, February 1979
  8. Flack, Darryl (September 2, 2009). "The day the Yamaha XS1100 won the Castrol Six-Hour – Part 1". Motor Sport Retro.com. Retrieved February 28, 2017.


This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.