Vertical pressure vessels installed in a structure on their way to Australia to a mining plant

The AS/NZS 1200 standard is a joint Australian/New Zealand Standard, for the requirements of pressure equipment which aims to promote safety and uniformity throughout Australia and New Zealand.

History

This Standard was originally published in 1931 as CB1 - SAA Boiler Code. It was subsequently issued in 1963 and 1967. In 1972, the Standard was issued under the designation AS 1200. The 2nd, 3rd and 4th editions were published in 1978, 1981 and 1988 respectively. In 1994 the Standard was jointed revised and issued under the designation AS/NZS 1200. The latest and 6th edition was published in 2000.[1]

Abstract

This Standard is a 'parent' document which sets out basic requirements and good practice for the design, materials, manufacture, examination, testing, installation, conformity assessment, commissioning, operation, inspection, maintenance, repair, alteration and disposal of pressure equipment (boilers, pressure vessels and pressure piping) but excluding gas cylinders, blast furnaces, pipelines, fire extinguishers, storage tanks to name a few.[1]

As a 'parent' document this Standard specifies specific requirements to pressure equipment by making reference to a range of Australian, New Zealand and other Standards.[1]

Requirements and Compliance

Equipment to be used in Australia or New Zealand must meet the following requirements:

  • Compliance with the Standards listed in this Standard, including international Standards, or those equivalently agreed between all parties.
  • Compliance with all applicable legal jurisdictions.
  • Compliance with the contract documents.[1]

When a selected Standard is used (local or international) as listed in this Standard, it shall be used in its entirety except when compliance with more appropriate requirements of other Standards. Irrespective of the Standard used, the Standard should only be considered as the minimal requirements and not necessarily holistic, therefore judgement needs to be exercised to ensure all relevant matters are covered.[1]

Pressure Equipment Standards

AS/NZS 1200 is a 'parent' Standard that specifies the requirements and Standards specific to pressure equipment. The following provides a sample of some of the Standards applicable to pressure equipment under this Standard.[1]

Function Equipment / Action Standard
General General Requirements AS/NZS 1200
Hazard levels AS 4343
Construction Boilers AS 1228
Pressure Vessels - General AS 1210-2010
Pressure Vessels - Advanced Design AS 1210-2010
Pressure Vessels - Cold-stretched Austenitic Stainless Steel Vessels AS 1210-2010
Pressure Piping - General AS 4041
Manufacturing AS 4458
Welding and Brazing Qualifications AS/NZS 3992
Examination and Testing AS 4037
Installation AS 3892
Use In-service Inspections AS/NZS 3788
Use Inspections AS 3873

Conformity Assessment

Australia

National

Pressure equipment is to be in accordance with AS/NZS 1200 per the Australian Government legislation as stipulated in Regulations 4.05(2)(d) and 4.51 (4)(b) of the Occupational Health and Safety (Safety Standards) Regulations 1994.[2]

Queensland

Some pressure equipment (excluding pressure piping) is regulated in the state of Queensland as per Schedule 4 (13) of the Workplace Health and Safety Regulation 2008.[3] In this Schedule, it refers to certain criteria being met per AS 4343, which scope is to classify hazard levels of pressure equipment to AS/NZS 1200.[4]

New South Wales

Pressure equipment is regulated in the state of New South Wales as per Clause 94 (a) of the Occupational Health and Safety Regulation 2001.[5] This Clause refers to AS 4343 and AS 1210, which are main Standards referenced in the 'parent' Standard AS/NZS 1200.[4][6]

New Zealand

Pressure equipment is to be in accordance with AS/NZS 1200 under New Zealand legislation as stipulated in section 3.4.1(1) of the Approved Code of Practice (ACOP) for Pressure Equipment (Excluding Boilers). This ACOP supports the requirements of the Health and Safety in Employment (Pressure Equipment, Cranes and Passenger Ropeways) Regulations 1999.[7]

References

  1. 1 2 3 4 5 6 "AS 1200 Pressure Vessels". SAI Global. Archived from the original on 9 July 2012. Retrieved 14 November 2011.
  2. "SR 1994 No. 414 Regulations as amended, taking into account amendments up to Occupational Health and Safety (Safety Standards) Amendment Regulations 2011 (No. 1)". Occupational Health and Safety Act 1991. ComLaw - Australian Government. Retrieved 15 November 2011.
  3. "How the legislation works". Workplace Health and Safety Queensland. Queensland Government. Retrieved 15 November 2011.
  4. 1 2 "Pressure equipment — Hazard levels". SAI Global. Archived from the original on 1 February 2013. Retrieved 14 November 2011.
  5. "Occupational Health and Safety Regulation 2001". Occupational Health and Safety Act 2000. New South Wales Government. Retrieved 15 November 2011.
  6. "Pressure Vessels". SAI Global. Archived from the original on 1 February 2013. Retrieved 14 November 2011.
  7. "Pressure Equipment (Excluding Boilers) - Approved Code of Practice". H&S Publications. Department of Labour. Archived from the original on 22 October 2011. Retrieved 15 November 2011.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.