An HP64000 system photographed in 1987.

The HP 64000 Logic Development System, introduced 17 September 1979, is a tool for developing hardware and software for products based on commercial microprocessors from a variety of manufacturers. The systems assisted software development with assemblers and compilers for Pascal and C, provided hardware for in-circuit emulation of processors and memory, had debugging tools including logic analysis hardware, and a programmable read-only memory (PROM) chip programmer. A wide variety of optional cards and software were available tailored to particular microprocessors. When introduced the HP 64000 had two distinguishing characteristics. First, unlike most microprocessor development systems of the day, such as the Intel Intellec and Motorola EXORciser, it was not dedicated to a particular manufacturer's microprocessors, and second, it was designed such that up to six workstations would be connected via the HP-IB (IEEE-488) instrumentation bus to a common hard drive and printer to form a tightly integrated network.

Models

  • 64100A, introduced in 1979. It was a desktop workstation which contained ten expansion slots for various optional cards. The initial offering of this workstation required an external hard disk for all disk storage, although the disk could be shared by up to six workstations via the HP-IB (IEEE-488) instrumentation bus.[1] Later, a dual floppy drive option was added so that a workstation could be used without the shared hard drive. This workstation's CPU was the BPC, the same custom HP 16-bit microprocessor found in the HP 9845C workstation. Software and hardware was offered to develop 8-bit and 16-bit microprocessors.
  • 64110A, a more portable workstation ("luggable") with five card slots, was introduced in 1983.[2] Its CPU was the same custom HP microprocessor as the 64100A.
  • 64120A card cage introduced in 1986.[3] It fit the same option cards as the 64100A and 64110A, and was connected via an IEEE-488 bus to a standard HP 9000 Series 300 workstation running the HP-UX operating system rather than using a specially designed workstation such as the 64100A and 64110A. The name "HP 64000-UX Microprocessor Development Environment" was used with these systems. Software and hardware was introduced for development of 32-bit microprocessors.
  • 64700A card cage was introduced in 1988.[4] It was marketed as a lower cost development system (compared to the 64120A) that could be operated with an IBM PC-compatible personal computer rather than a workstation.[5] Cards for this system carried the numbers 647xx, and were not compatible with the other systems.

Description

HP 64000 functional block diagram

Terminology

As shown in the block diagram to the right, a 64000 system consisted of a number of components whose names had specific definitions:

  • Mainframe is the physical workstation or card cage holding the option cards.
  • Host is the processor that operates the mainframe. In the 64100A and 64110A the Host Bus is the workstation processor's address, data, input/output and control buses, which also connect to the cards in the card cage.
  • User system is the microprocessor system being developed. The terms user processor and user memory describe those components in the system being developed.
  • Emulation or Emulator refers to optional cards and other hardware that are connected to the mainframe via the plug-in cards and can replace the processor and/or memory in the user system. Emulation and analysis cards are interconnected with an Emulation Bus that is completely separated from the Host Bus.

Software Development

The 64000 provided a file system and text editor for writing software. There was a generic assembler / linker (manual Bitsavers), Pascal compiler (manual Bitsavers), and C compiler (manual Bitsavers), which were supplemented with add-on cross-assemblers and cross-compilers for each particular microprocessor. A list of these by product number is:

MicroprocessorAssembler Product #Assembler ManualPascal Compiler Product #Pascal Compiler ManualC Compiler Product #C Compiler Manual
Motorola 6800/1/2/3/864841ABitsavers64811ABitsavers64821A
Motorola 680964844ABitsavers64813A (Disk image at HPCM)Bitsavers64822A (Disk image at HPCM)Bitsavers
Motorola 68000/08/1064845A (Disk image at HPCM*)Bitsavers64815A (Disk image at HPCM)Bitsavers64819ABitsavers
Intel 804864846A (Disk image at HPCM)Bitsaversnonenone
Intel 805164855A (Disk image at HPCM)nonenone
Intel 8080/808564840A64810ABitsavers64826A
Intel 8086/87/88/186/18864853A (Disk image at HPCM)64814A (Disk image at HPCM)64818A (Disk image at HPCM)
Zilog Z8064842A (Disk image at HPCM)Bitsavers64823A (Disk image at HPCM)64824A (Disk image at HPCM)
Zilog Z864850Anonenone
Zilog Z800064854Anonenone
RCA 180264848Anonenone
MOS Technology 6501/650564843Anonenone
Texas Instruments TMS990064847Anonenone
Texas Instruments TMS32064858Anonenone
Fairchild F864849Anonenone
MIL-STD-1750A64857Anonenone

* HPCM is the Hewlett Packard Computer Museum

In addition, there was a Pascal "Host Compiler", product number 64817A manual at Bitsavers, disk image at HPCM, which could be used to write programs to execute on the workstation host processor.

In-Circuit Emulation

HP64100A Logic Development System emulating a microprocessor

The 64000 system, through the use of optional cards and software, could perform in-circuit emulation of a variety of microprocessors and their memory.[1][2] A complete emulation system typically consisted of:

  • A microprocessor emulator controller card, specific to each microprocessor.
  • An emulation "pod" or "probe", which contained interface electronics and was an external module to the mainframe. The processor in the user system was removed from its socket, and a cable from the emulation pod was connected in its place. The emulation pod contained a copy of the user processor that ran program code just as the user processor would, and it appeared to the user system as the normal processor.
  • An emulation memory controller card and one or more emulation memory cards. The emulation memory could be used to substitute for memory in the user system so that, for instance, user program code could be placed in the emulation memory and executed rather than needing to program ROM chips.
  • An "internal" analyzer card, which was a logic analyzer that monitored the operation of the emulated processor and memory.
  • Emulator software that allowed the operator to start and stop the emulated processor, examine the contents of memory and register locations, measure signal timing, observe program flow, and so on.

The photo at right shows a 64100A workstation emulating the processor of a user system via an emulator pod. The photo also shows a data acquisition pod for an "external" logic analyzer card in the 64100A that was measuring additional digital signals in the user system.

MicroprocessorEmulator Controller Card Product #ManualEmulation Pod Product #ManualEmulation Software Product #Manual
Motorola 680064211ABitsavers64212ABitsavers64210ABitsavers
Motorola 6801/680364256A64255A64256A
Motorola 6802/680864211ABitsavers64213ABitsavers64210ABitsavers
Motorola 680564191ABitsavers64192A/64193ABitsavers64192A (Disk image at Bitsavers)
Motorola 680964214ABitsavers64215A/64216ABitsavers64215A (Disk image at Bitsavers)Bitsavers
Motorola 68000/6800864243A/64244A64243A/64244A64243A (Disk image at HPCM)Bitsavers
Motorola 6801064271A64249A64249A
Intel 804864261A64262A64262A (Disk image at HPCM)
Intel 805164263A64264A64264A
Intel 808064201A64202A64202A
Intel 808564201A64203A64203A
Intel 808664271A64222A64222A (Disk image at HPCM)
Intel 808864271A64226A64226A
Intel 8018664223A64224ABitsavers64224A
Intel 8018864223A64225A64225A
Zilog Z8064251A64252A64252A (Disk image at HPCM)
Zilog Z8001/800264271A64232A/64233A64232A/64233A

* HPCM is the Hewlett Packard Computer Museum

Emulator control boards connected to both the host (mainframe) bus and the emulation bus. They acted to pass control signals and data between the host and emulated systems. Depending on the model, the control board might also contain hardware to flag illegal opcodes or memory accesses or to act as an internal logic analyzer.

Memory Emulation allows RAM and/or ROM in the user system to be replaced by memory in the 64000 system. Two emulation memory controller boards were offered:

  • 64151A Emulation Memory Controller (manual at Bitsavers), which had 16 address lines so could address 64 KB of memory, and
  • 64155A Wide Address Memory Controller (manual at Bitsavers), which had 24 address lines so could address 16 MB of memory.

Memory maps for the user system could be specified in terms of RAM, ROM and protected memory. Attempted writes to ROM or accessing of protected memory was detected by the memory controller and could trigger actions such as program breakpoints.

Memory cards of various capacities of static RAM were offered. The 64152B, 53B and 54B cards provided 32, 16 and 8 KB, respectively, and the 64161A, 62A and 63A cards provided 128, 64 and 32 KB, respectively.[6] They could each be configured for 8-bit or 16-bit data buses. Memory cards were connected together and to the memory controller through an emulation memory bus. Accesses to emulation memory by either the host or user systems was through the controller card.

Once the emulated processor and memory took the place of the processor and memory in the user system, the designer could write and compile program code, load it into emulation memory and start the user system, running the program in the emulated processor.

Analysis

A 64000 system could act as a logic analyzer to measure digital signals within the user system. Two types of logic analysis cards were offered, "internal" analyzers which measured signals directly off the emulation bus within the mainframe, and "external" analyzers which used separate probes to physically connect to elements of the user system. Similar to the processor and memory emulation products, analysis functions were often divided into controller cards and data acquisition cards. Some of the emulation processor controller cards offered internal analysis functions without separate hardware.

Logic analysis hardware was also divided into state analyzers and timing analyzers. The former measured signals in synchronization with a system clock and could, for example, record the states of the address, data and control buses in the user system at each CPU cycle. This data was normally presented as a trace, showing the value on each bus for each CPU cycle. For many microprocessors, an "inverse assembler" was available that would convert values measured on the data bus to Opcodes for the user processor.

The second form of logic analysis was timing analysis. A timing, or asynchronous logic, analyzer measured digital signals at specified time intervals, not necessarily synchronized to the user system clock. Such analysis could be used to find glitches or verify digital signals had proper timings.

In addition to these logic analyzer functions, "software analysis" options were available. These tools acted as what are now commonly called debuggers and profilers.

A list of analysis products is:

Product NumberDescriptionManual
64300AInternal Logic Analyzer
64302AInternal Wide Logic AnalyzerBitsavers
64310ASoftware Performance AnalyzerBitsavers
64331A68000 High Level Software Analyzer
64601ATiming/Hardware Analyzer ControllerBitsavers
64602A8 Channel Timing AcquisitionBitsavers
64604A8 Channel Timing ProbeBitsavers
64621AState/Software Analyzer ControllerBitsavers
64622A40 Channel State AcquisitionBitsavers
64623A20 Channel State AcquisitionBitsavers
64635A20 Channel State Data Probe
64636A8 Channel State Clock Probe

Similar to the way the emulation hardware used "pods" with interface hardware tailored to each microprocessor, the analysis hardware used preprocessors to act as an interface to the microprocessor. Aside from the 64304A Emulation Bus Preprocessor (manual at Bitsavers), each of the CPU specific preprocessor interfaces was a circuit board that fit within the 64650A General Purpose Preprocessor module (manual at Bitsavers). That, in turn, connected to the logic analyzer card cables.

Product NumberDescription
64304AEmulation Bus Preprocessor
64653A8086/8088 Preprocessor Interface
64655A8085 Preprocessor Interface
64657A80286 Preprocessor Interface
64658A80186/80188 Preprocessor Interface
64670A68000 Preprocessor Interface
64671A6809 Preprocessor Interface
64672A6800/6802 Preprocessor Interface
64673A68008 Preprocessor Interface
64674A68000/68010 Preprocessor Interface
64680AZ8001 Preprocessor Interface
64681AZ8002 Preprocessor Interface
64683AZ80 Preprocessor Interface
64690ANSC800 Preprocessor Interface

PROM Programmer

The 64100A has a space to the right of the keyboard that can accept a PROM programmer module. A common PROM programmer control card, the 64500A (manual at Bitsavers), was installed in the card cage. At least 11 programmer modules, numbered from 64502A to 64520A were available for a variety of PROM and programmable microcontroller chips from different manufacturers.

MAME Emulator

An emulation of the 64100A workstation is part of the MAME (Multiple Arcade Machine Emulator) system, under Manufacturer HP and titled "HP 64000". The emulator is open source and the source code is available.

References

  1. 1 2 Saponas, Thomas A.; Kerr, Brian W. (October 1980). "Logic Development System Accelerates Microcomputer System Design" (PDF). Hewlett-Packard Journal. 31 (10): 3–12. Retrieved 22 November 2023.
  2. 1 2 Davis, Michael W.; Scharrer, John A.; Wickliff, Robert G. (March 1983). "Extensive Logic Development and Support Capability in One Convenient System" (PDF). Hewlett-Packard Journal. 34 (3): 3–5. Retrieved 14 July 2018.
  3. HP Computer Museum entry for 64120A.
  4. HP Computer Museum entry for 64700A.
  5. Hewlett Packard Catalog (PDF). The Hewlett Packard Archive. 1989. pp. 625–626. Retrieved 14 July 2018.
  6. Bitsavers
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.