Advantages

• Pushers offer higher processing capacities than batch filtering centrifuges such as vertical basket and inverting filter.
• Provides the best washing characteristics of any continuous centrifuge due to control of retention time and uniform cake bed.
• Gentle handling makes pushers better suited for fragile crystals.

Limitations

• Pushers require a constant feed flood due to their continuous nature.
• Although high capacities may be preferred, this may result in longer residence time.
• Typical particle sizes must be at least 150 μm and average 200 μm.
• A high viscosity feed lowers throughput.
• Pushers have a limited liquid filtration capacity and requires fast-draining materials, since it must form a cake within the period of one stroke.

Single-stage

Single-stage units can be cylindrical or cylindrical/conical with a single long basket and screen

• Can maximize solids volumetric capacity
• Resulting cake can shear or buckle due to unstable operation of the longer screen length
• Capacity may be slightly less than with multistage units
• Lesser fine losses due to small contact of particles with the slotted screen and no reorientation of crystals between stages
• Used to achieve stability for low-speed operation

Multi-stage

Multistage (two-, three-, or four- stage designs): cylindrical and cylindrical/conical

• Most common
• Greater flexibility due to higher filtration capacity
• Reorientation can enhance wash effect on the latter portion of the first stage and through transition onto second stage

Cylindrical/conical

Feed distributor design: conical/cylindrical or plate

• Optionally applied for single- and two stage- designs.
• Cylindrical feed section combined with a sloping design towards the discharge end
• Axial component of force in the conical end aids solids transport
• Lower production costs compared to that of baskets

Feed

Pushers utilise the cake layer to act as a filter, hence the feed normally contains high solid concentration containing fast draining, crystalline, granular or fibrous solids. The solid concentration ranges from 25-65 wt%.^[2] The mean particle size suitable for pushers must be at least 150 µm. The capacity depends on the basket diameter and ranges from 1 ton/h to 120tons/h.^[4]

Operations

The cake is under centrifugal force. It becomes drier as it progresses in the basket and is discharged from the pusher basket into the solid discharge housing (pusher centrifuge operation). The stroke length ranges from 30 to 80 mm and the stroke frequency is between 45 and 90strokes/min.^[4]

The push efficiency is defined as the distance of the forward movement of the cake ring divided by the stroke length. The push efficiency is a function of the solid volumetric loading, which results in self-compensating control of varying rates. Up to 90% push efficiency is achievable depending on the cake properties.^[4] dQ3ET42T

Filtration rate

The equation for the filtration rate, Q:^[4]

(1) ${\displaystyle Q=(\pi b\rho K\Omega ^{2}(r_{b}^{2}-r_{p}^{2}))/(\mu [r_{b}/r_{p}])+(KR_{m})/r_{b})}$

(2) ${\displaystyle \alpha K\rho _{s}=1}$

Where ${\displaystyle \mu }$ and ${\displaystyle \rho }$ are viscosity and liquid density, respectively. ${\displaystyle \Omega }$ is the angular speed, ${\displaystyle K}$ is the average cake permeability, which is related to equation (2), ${\displaystyle r_{p},r_{c}}$, and ${\displaystyle r_{b}}$ are the radius of the liquid surface, cake surface and filter medium adjacent to the perforated bowl respectively, ${\displaystyle R_{m}}$ is the combined resistance, ${\displaystyle \alpha }$ is the specific resistance and ${\displaystyle \rho s}$ is the solid density.

The numerator describes the pusher's driving force, which is due to the hydrostatic pressure difference across the wall and the liquid surface. The denominator describes the resistance due to the cake layer and the filter medium.

Process variables

Performance is a function of many parameters, including particle size, viscosity, solid concentration and cake quality.^[2]

Particle size/porosity

To create the cake layer, the particle size has to be as large as practically possible. Larger particle size increases the porosity of the cake layer and allows feed liquid to pass through. Particle shape is equally important, because it determines the surface area per unit mass. As it decreases, less surface area is available to bind moisture, providing a drier cake.^[2]

Viscosity

Filtration rate is a function of the viscosity of the feed fluid. From equation (1), the relationship of the filtration rate is inversely proportional to the viscosity. Increasing viscosity means adding resistance to the fluid flow, which complicates separation of the fluids from the slurry. Consequently, the throughput of the pusher is de-rated.^[2][4]

Solid concentration

In most cases the solids discharge capacity/hydraulic capacity is not the limiting factor. The usual limitation is the filtration rate. Therefore, more solids can be processed by increasing the feed slurry concentration.

Cake quality

The cake quality is determined by the purity and the amount of volatile matter.

Design process

Overall approach:^[4]

• Define the problem
• Outline process conditions
• Make preliminary selections
• Develop a test program
• Test sample batches
• Adjust process conditions as required
• Consult equipment manufacturers
• Make final selection and obtain quotes

Equipment sizing

Variables considered in sizing equipment:

• Feed rate
• Feed concentration
• Cake thickness
• Bulk density
• Long and short baskets
• Single and two-stage baskets
• Individual drive for rotor and hydraulic system
• Easy accessibility for maintenance
• Energy consumption
• Previous applications

Equipment selection

Equipment selection is based upon test results, references from similar processes and experience and considered in terms of:

• Cost, quality and productivity
• Financial modeling

Optimising performance

For conical and cylindrical designs and assembly, the cone slant angle should not exceed sliding friction cake angle. Otherwise it would result in high vibration and poor performance.^[4]

In order to optimise capacity and performance, it is desirable to pre-concentrate the feed slurry as much as possible. Some designs have a short conical section at the feed end for thickening within the unit, but generally it is preferable to thicken before entering the centrifuge with gravity settlers, hydrocyclones or inclined screens, producing a higher concentration of solids.

The volumetric throughput for multistage designs can be increased by increasing the forced cake height while still retaining acceptable push efficiency.

Design selection

Selection of designs is usually done by scale-up from lab tests. Test data analysis should be rationalised in preparation for equipment scale-up. Computer-aided design software can assist in design and scale-up. Pilot-testing and rollout then follows.^[5]

Production

The majority of liquid contained within the mixture is drawn out at an early stage, in the feed zone of the slot screen. It is discharged into the filtrate housing. After formation of solid cakes, the main by-product produced is water, which may be used in all sorts of industrial usage. Filtration cakes are washed using nozzles or waste baskets.

Post-treatment

Post-treatment processes are a function of the specifics of the waste stream and are diverse.^[6]

Stages

B&P Process Equipment and Systems (B&P) makes the largest single-stage pusher centrifuge, which they claimed to be superior to multistage designs.^[7] They claimed that additional impurities enter the liquid housing due to additional particles tumbling in each stage. The problem can be overcome by using a shorter inner basket with smaller diameter between the pusher plates and the basket and enabling pusher movement to take place between the pusher plate and the basket as well as between the inner basket and the outer basket. Compared to single-stage pushers that have pusher movement only between pusher plate and basket, multistage centrifuges have the advantages that the cake height is reduced, filtration resistance is lower and lesser force is required.

Push hesitation

Push hesitation holds the pusher plate in the back stroke, allowing the cake to build on itself. The cake acts as the filtering media that can even capture finer solids. This reduces the loss of solids passing through the wedge slots. Although this modification reduces capacity, it has helped improved the solid capture efficiency and make pusher centrifuges applicable to smaller particles.^[2]

Horizontal split process housing

This allows the removal of the rotating assembly without disassembling the basket and pusher centrifuge from the shafting assembly.

Integral hydraulics

An automated mechanism allows the system to operate independently.

Seals

Shaft seals eliminate the possibility of cross-contamination between the hydraulic and process ends. Options include a centrifugal liquid ring seal and a non-contacting inert gas purged labyrinth seal that eliminates leakage.

Pre-drained funnel

The pre-drained funnel removes a portion of the feed fluid through a puncture surface. This feature helps to concentrate the feed, which is especially important for drainage-limited applications. However the funnel cannot be back-washed therefore this feature is only available for crystals that tend not to back-crystallise.

Integrated thickening

Integrating the thickening function enables the pusher to be loaded with mixture with as little as 30-35% wt of solid. It also reduces process costs of solid-liquid separation by as much as 20%.^[8]